IR
Industrial Rental Co
Planning guide

How to size a rental chiller: tonnage, ambient derate, and process load

A rental chiller is sized from the actual cooling load in tons, not from the failed unit's nameplate alone. Start with tons of refrigeration, adjust for ambient temperature and altitude, add margin for process swings, and confirm whether the site needs air-cooled or water-cooled equipment before requesting quotes.

By Industrial Rental Co Editorial Team Reviewed

Key facts

  • One ton of refrigeration removes 12,000 Btu per hour, the rating basis set by ANSI/AHRI Standard 550/590 for water-chilling packages (AHRI).
  • Air-cooled chillers lose usable capacity as ambient temperature climbs; budget derate rather than assume nameplate tons hold in July.
  • A chiller sized for full-load duty and one sized for part-load duty are not the same purchase decision, per DOE's Federal Energy Management Program guidance on part-load efficiency (FEMP).
  • Power availability, not tonnage, is often the item that blocks a temporary chiller install.

Start with the load, not the failed unit's nameplate

A rental request is easier to scope when it states a real cooling load in tons, not just "replace what we had." A failed chiller's nameplate is a reasonable starting point, but nameplate capacity assumes standard AHRI rating conditions. For water-cooled units, that is 44°F leaving and 54°F entering chilled-fluid temperature, with 85°F entering and 94.3°F leaving condenser-fluid temperature (AHRI Standard 550/590-2023). Your actual site conditions rarely match those exactly, which is why a real load estimate beats a nameplate copy.

If you have a heat load study, process cooling data sheet, or building automation trend for the equipment being served, that is the strongest input. If you do not, work from connected load: process heat exchangers, injection molding tonnage, server room kW, or comfort-cooling square footage, and let the provider's engineer size against it.

"One ton of refrigeration equals 12,000 Btu per hour of heat removal, the basis for chiller capacity ratings under ANSI/AHRI Standard 550/590." Source: AHRI Standard 550/590-2023, Air-Conditioning, Heating, and Refrigeration Institute

Worked example 1: process cooling replacement

A food processing plant's 150-ton water-cooled chiller fails mid-shift. The plant does not have a current heat load study, but the failed unit's nameplate reads 150 tons at standard AHRI conditions, and the process runs near full load most of the shift.

  • Start point: 150 tons nameplate
  • Add 10 to 15 percent margin for pickup after a cold start and for any process expansion since the original unit was specified: 165 to 172 tons
  • Confirm water-cooled vs air-cooled: the original unit was water-cooled. A rental water-cooled package needs a temporary cooling tower and condenser water loop, which changes the footprint and the quote
  • Result: request quotes for a 175-ton-class water-cooled package with tower, sized from nameplate plus margin, not an exact 150-ton match

Worked example 2: data center cooling with ambient derate

A data center in Phoenix needs 100 tons of supplemental air-cooled cooling for a planned electrical outage in August, when daytime highs run well above the 95°F ambient that many air-cooled chiller ratings assume.

  • Base need: 100 tons at standard rating conditions
  • Air-cooled chiller capacity drops as ambient climbs above the unit's design point; the exact derate curve is unit-specific, so ask the matched provider for the manufacturer's derate table at your peak design-day temperature rather than assuming a fixed percentage
  • Practical approach: request quotes sized to the 100-ton cooling requirement and state the peak ambient design temperature (for example, 110°F) so providers can select or oversize equipment to deliver 100 tons of usable capacity at that condition, not 100 tons of nameplate that underperforms in the heat
  • Result: the RFQ states the required tons of usable cooling at peak ambient, and the provider's engineering determines the nameplate size needed to hit that number

High-ambient states carry this derate math every summer, not just during one outage. For a look at how Arizona sites plan around it, see chiller rental in Arizona.

Sizing inputs by scenario

ScenarioPrimary sizing inputWhat changes the quote
Failed unit replacementNameplate tons + 10-15% marginWater- vs air-cooled, condenser loop needs
No load study availableConnected equipment (tons, kW, or CFM served)Provider engineering review before firm quote
High-ambient climateTons of usable capacity at peak design temperatureAir-cooled derate, possible oversizing
Data center or process critical loadRedundancy requirement (N+1 or 2N)Multiple smaller units vs one large chiller
No spare site powerAvailable voltage, phase, and ampsMay require a rental generator alongside the chiller

Air-cooled or water-cooled: the second decision

Tonnage answers "how much cooling," not "what kind of chiller." Air-cooled units reject heat to outside air and arrive closer to self-contained, which suits sites with tight footprints, no cooling tower water source, or fast mobilization needs. Water-cooled units are more efficient at larger tonnages but need a temporary cooling tower and a condenser water loop, so the rental becomes a package rather than a single unit, and the site needs makeup water and blowdown drainage.

  • Air-cooled: simpler setup, no tower, moderate footprint, ambient-dependent capacity
  • Water-cooled: better efficiency at scale, needs tower plus condenser loop, needs a water source and drainage plan
  • Mixed sites sometimes rent a smaller air-cooled unit for immediate coverage while a larger water-cooled package mobilizes

Power is often the real constraint

A correctly sized chiller can still be the wrong quote if the site cannot feed it. Large rental chillers draw enough power that transformers, cable, and switchgear are typically quoted as separate line items from the chiller itself. Confirm available voltage, phase, and spare amperage before the RFQ goes out. Then a provider can tell you immediately whether the site supports the unit, or whether a rental generator belongs in the same request. Work involving temporary electrical tie-ins and equipment isolation should follow the site's lockout and tagout procedures during hookup, consistent with OSHA's control-of-hazardous-energy standard, 29 CFR 1910.147 (OSHA).

  • List available voltage, phase, and spare amperage in the RFQ
  • Ask directly whether the site needs a rental generator alongside the chiller
  • Confirm who handles the electrical tie-in and under what lockout and tagout procedure
  • Share condenser water source and drainage plan for water-cooled requests

What to put in the RFQ

A complete request moves faster through matching and returns comparable quotes from multiple providers.

  • Required tons of usable cooling, and at what ambient or process condition
  • Air-cooled or water-cooled preference, or "provider recommends"
  • Target chilled-water supply and return temperatures
  • Available site power (voltage, phase, amperage)
  • Redundancy requirement, if any (N+1, 2N)
  • Rental duration and start-date window
  • Site access, indoor or outdoor placement, and any crane or rigging needs

For the technical, site, and project fields a planned request should include in full, see the rental equipment spec checklist.

What this costs to budget

Tonnage and chiller type have the most effect on the rental rate. Power hookup and ancillaries form the next main cost layer. See the chiller rental cost guide for current planning ranges by tonnage and type. These figures are planning estimates, not quotes. Each matched provider sets its own price for your specific job. That price reflects the location and how long you need the rental.

FAQ

Common questions

How many tons of cooling do I need for my facility?

Start from a heat load study or building automation trend if you have one. Without one, use connected load: process heat exchangers, machine cooling requirements, or server room kW, and share that with a matched provider so their engineering can confirm the tonnage before you commit to a number.

Does ambient temperature really change how many tons I need?

Yes, for air-cooled chillers. Capacity drops as ambient temperature rises above the unit's rated design point. State your peak design-day temperature in the RFQ so providers can size to deliver the tons you need under real conditions, not nameplate tons that only hold at standard rating conditions.

Should I rent an air-cooled or water-cooled chiller?

Air-cooled suits tight footprints, no available tower water, and faster mobilization. Water-cooled is more efficient at larger tonnages but needs a temporary cooling tower and condenser water loop. If your facility's existing chiller was one type, matching it usually simplifies the tie-in.

What margin should I add over the failed unit's nameplate?

A common starting range is 10 to 15 percent above nameplate to cover startup pickup and any load growth since the original unit was specified, but the right margin depends on your process. Share your actual load data with a matched provider rather than relying on a fixed rule.

Does a rental chiller need its own power supply?

Often, yes, beyond a simple connection. Larger rental chillers draw enough power that transformers, cable, and switchgear are commonly quoted separately, and a site without spare capacity may need a rental generator in the same request.

How is chiller tonnage different from boiler horsepower?

They measure different things. A ton of refrigeration is 12,000 Btu per hour of heat removal. This is the standard for cooling equipment. Boiler horsepower measures steam or hot-water heat output. One boiler horsepower is roughly 34.5 pounds of steam per hour. Size and quote temporary cooling separately from temporary heat if your facility needs both. See the boiler sizing guide for the heating side.

Get matched with qualified providers

Submit specs once. Response times vary by location and provider availability. Reviewed July 2026.

Emergency requestPlanned RFQ